How to Maintain Water Bottle with Straw
Introduction on how to maintain MIKI HOUSE Water Bottle with Straw. To learn more about how to maintain these sets, please see below.
Products
Water Bottle with Straw（15-4158-684）
Volume: 340mL
Water Bottle with Straw（15-4146-681）
Volume: 340mL
Water Bottle with Straw（15-4116-383）
Volume: 340mL
Water Bottle with Straw（65-4062-825）
Volume: 340mL
Instructions for use
Part Names
How to Set the Spout into the Inner Lid
When setting the spout, push it through the spout hole from under the inner lid, and pull it until the spout stopper is securely in place. When removing the spout, hold the bottom of the spout and pull until it is removed.
*If you hold the straw instead of the spout when removing, only the straw will detach.
How to Attach the Shoulder Strap
Make sure the strap clasp is correctly set.
Microwave, Dishwasher and Dryer Use
*Do not put this item in the microwave.
Warnings for Dishwasher and Dryer Use
- Do not wash in industrial dishwashers or industrial dryers.
- Avoid cleaning in commercial dishwashers.
- Do not stack in the dishwasher or dryer. Stacking may cause distortion.
- Please do not stack this product on other things. This may cause deformation.
- Please check the labels and instruction manuals of the dishwasher/dryer before using.
- Please only use after thoroughly checking the display and instruction manuals of the dishwasher and detergent.
- Do not place in the heater portion of the dishwasher. This may burn or melt the product, or cause smoke.
- Do not drop this product on the heater part of the dishwasher. Doing so may cause smoke, etc.
- Remove shoulder strap when washing or drying.
- Remove the shoulder strap when washing in the dishwasher.
Warnings for Usage
- Do not place near fire.
- Cease use immediately if product cracks or chips.
- Do not use the shoulder strap to hang product around the neck or swing product around. This may cause accidents.
- Sudden temperature changes or leaving the product in a hot car may cause the air inside to expand and the contents to explode.
- This product is not a cold insulation product.
- Do not fill with hot beverages. This may cause burns.
- This product is not completely leakproof and should always be used upright. Laying it on its side may cause leaks.
- Make sure the rubber seal and spout are correctly set and check for leaks before use.
- When carrying the product in a bag, etc., be sure to put it in a waterproof bag such as a plastic bag.
- When washing, soak a sponge or soft cloth with a neutral dish detergent, hand wash with lukewarm water, and dry thoroughly.
- Do not scrub with a scrubbing brush or polishing powder.
- Do not use alkaline detergents or orange oil detergents as they may cause the designs to peel off or discolor.
- When bleaching, please use kitchen chlorine bleach. Excessive bleaching will damage the product quickly, so please follow package instructions for each bleach.
- Do not bleach or chemically disinfect the lid. This will cause the metal parts to corrode and damage.
- Avoid disinfecting with alcohol or boiling water.
- For chemical disinfection, use a gentle disinfectantfor babies and follow the package instructions for each disinfectant.
- Avoid steam disinfecting in the microwave.
- Leaving oil and oily substances on the designs may cause them to peel off.
- Do not use for the following beverages. <Carbonated drinks> The water pressure may cause leakage. <Beverages containing pulp> May cause leaking. clogging, etc.
- Do not freeze while filled. This may cause damage.
- Biting down on the spout may cause damage. lf the spout or rubber seal become damaged, please replace it with new parts (additional charge).
Temperature Resistance
| Part Names | Highest Temperature | Lowest Temperature |
|---|---|---|
| Lid | 100℃ | -20℃ |
| Inner Lid | 120℃ | -20℃ |
| Button | 120℃ | -20℃ |
| Cup | 120℃ | -20℃ |
| Straw | 140℃ | -20℃ |
| Spout | 140℃ | -20℃ |
| Seal | 140℃ | -20℃ |
| Strap Clasp | 80℃ | -20℃ |
Raw Resin and Materials Used
| Part Names | Raw Resin | Material |
|---|---|---|
| Lid | PET | |
| Inner Lid | Polypropylene | |
| Button | Polypropylene | |
| Cup | Polypropylene | |
| Straw | Silicone Rubber | |
| Spout | Silicone Rubber | |
| Seal | Silicone Rubber | |
| Strap Clasp | ABS Resin | |
| Spring | Stainless Steel | |
| Pin | Brass |
